1-800-336-2598   Download Catalog Contact Us Exhibits Order Catalog Products Home
THREADED LIFTING SYSTEM
DR | Threaded | Wire Rope | A-Anchor | Coils | Flat Steel | Manhole
Hebefix D8 | Transfix Anchor | Heba-T | Stone Strong | Recon & AW-Anchors
 
Uses innovative engineering to provide superior performance for edge lifting and tilting thin precast panels, with minimal or no patching. Supplied with color coded reinforcement clip for easy identification. Shear loading requires the use of one shear bar and one shear bow per anchor. Upper section of anchor is plated.
 
WAVED TAIL ANCHORS
Extended waved tail provides
exceptional tensile capacity in thin panels.
Can also be used in shear with
addition of a shear bow.
Part
Number		 Color Code Tension Capacity Tons Shear Capacity Tons Thread
Size (D)		 Anchor Length (L) Min. End Distance Min. Panel Thickness Tension Min. Panel Thickness Shear
WTA005 Orange 0.5 0.25 Rd12 5-3/8” 6” 2-1/4” 3”
WTA008 White 0.8 0.4 Rd14 6-5/8” 8” 2-1/2” 3-1/4”
WTA012 Red 1.2 0.6 Rd16 7-3/4” 8” 2-3/4” 3-3/4”
WTA016 Pink 1.6 0.8 Rd18 9-1/4” 10” 3-1/4” 4”
WTA020 Light Green 2 1 Rd20 10-1/8” 11” 3-1/2” 4-1/2”
WTA025 Dark Grey 2.5 1.25 Rd24 13-3/4” 12” 4” 5”
WTA040 Emerald Green 4 2 Rd30 17-3/4” 14” 4-3/4” 6”
WTA063 Light Blue 6.3 3.15 Rd36 22-3/8” 16” 6-1/4” 8”
WTA080 Light Grey 8 4 Rd42 24-3/8” 20” 7” 9-1/2”
WTA125 Yellow 12.5 6.25 Rd52 34-5/8” 24” 8” 11”

Tension capacities provide safety factor of approximately 4:1 in 2200 psi concrete.
 
THREADED SOCKET ANCHORS
Can be used for a wide range of applications in precast construction such as lifting anchors for beams and grinders, wall and floor slabs, etc. To develop the load rating, a bent reinforcement bar must be inserted through the cross hole. Stocked in plated finish.		  

 

Minimum panel
thickness = 2 x E.
If two or more anchors are used, minimum spacing = 2 x F.
Allowable Shear Capacity is valid for loads in any direction, parallel to the face of the concrete with shear bows.
Additional shear capacity can be achieved by reinforcing Threaded Socket Anchors in the ways shown on the following page.

 
Part Number System Load Code Sys. Load
Rating Tons		 Thread Size (D) Anchor Length (L) Min. Panel Thickness (2 x e) Min Edge Distance (F)
TSA005 Orange 0.5 Rd12x1.75 1-9/16” 2-1/2” 6”
TSA008 White 0.8 Rd14x2.0 1-7-8” 2-3/4” 8”
TSA012 Red 1.2 Rd16x2.0 2-1/8” 3-1/4” 8”
TSA016 Pink 1.6 Rd18x2.5 2-9/16” 3-3/4” 10”
TSA020 Light Green 2 Rd20x2.5 2-3/4” 4-1/2” 11”
TSA025 Dark Gray 2.5 Rd24x3.0 3-1/16” 5” 12”
TSA040 Emerald Green 4 Rd30x3.5 4-1/16” 5-1/2” 14”
TSA063 Light Blue 6.3 Rd36x4.0 4-7/8” 8-3/4” 16”
TSA080 Light Gray 8 Rd42x4.5 5-3/4” 9-1/2” 20”
TSA125 Yellow 12.5 Rd52x5.0 7-5/8” 11” 24”

Tension capacities provide safety factor of approximately 4:1 in 2200 psi concrete.
 
TENSION VEES
Use with Threaded Socket Anchor Wire or Bar Size J [ in ] Length for 2,200 psi concrete K22 [ in ] (L) Length for 3,600 psi concrete K36 [ in ] (L) Bend Diameter [ in ]
TSA 005 D-5 8-1/2 6-3/4 1
TSA 008 D-8 10 8 1-1/4
TSA 012 # 3 12 9-1/2 1-1/2
TSA 016 # 3 16-1/2 12-1/2 1-1/2
TSA 020 # 4 17 13-1/2 2
TSA 025 # 4 18-1/2 14 2
TSA 040 # 5 25-1/2 19-1/2 2-1/2
TSA 063 # 6 32 24-3/4 5-1/2
TSA 080 # 8 33 25-1/2 7
TSA 125 # 9 46 35-1/2 8
 
FLAT STEEL ANCHORS
Ideal for backstripping or face lifting thin precast panels. Supplied with color coded reinforcement clip for easy identification. Tension loads require the use of two Tension Bars per anchor. Shear loads require the use of two Tension Bars and one Shear Vee per anchor. Stocked in plated finish.
Part Number System Capacity (Tons) Thread Size (D) Anchor Depth (L) Base Length (A) Base Width (B) Base
Thick. (C)
FSA005 0.5 Rd12x1.75 1-3/16” 1-3/8” 1” 1/8”
FSA008 0.8 Rd14x2.0 1-5/16” 1-3/8” 1-3/8” 1/8”
FSA012 1.2 Rd16x2.0 1-3/8” 2” 1-3/8” 1/8”
FSA016 1.6 Rd18x2.5 1-3/4” 2-3/8” 1-3/4” 3/16”
FSA020 2 Rd20x2.5 1-7/8” 2-3/8” 2-3/8” 3/16”
FSA025 2.5 Rd24x3.0 2-1/8” 3-1/8” 2-3/8” 3/16”
FSA040 4 Rd30x3.5 2-7/8” 3-7/8” 3-1/8” 1/4”
FSA063 6.3 Rd36x4.0 3-5/16” 5-1/8” 3-7/8” 1/4”
FSA080 8 Rd42x4.5 3-7/8” 5-1/8” 5-1/8” 5/16”
FSA125 12.5 Rd52x5.0 4-5/8” 5-7/8” 5-1/8” 5/16”
Tens. Bar Part No Use W/Flat Steel Anchor Reinf. Tens. Capacity (LBS) Minimum Edge Distance (F) Minimum Panel Thick. (P) Dia. (R) Overall Length (H) Crown Length (J) Offset (K)
FTB005 FSA005 1,060 7” 2-3/4” 1/4” 10” 2-3/8” 1-1/8”
FTB008 FSA008 1,720 7” 3-1/8” 1/4” 14” 2-3/8” 1-3/8”
FTB012 FSA012 2,580 9-7/8” 3-3/8” 5/16” 16-1/2” 3-1/2” 1-3/8”
FTB016 FSA016 3,440 11-3/4” 3-3/4” 5/16” 21” 3-1/2” 1-1/2”
FTB020 FSA020 4,300 11-3/4” 4” 5/16” 25-1/4” 3-1/2” 1-1/2”
FTB025 FSA025 5,360 15-3/4” 4-1/2” 3/8” 25-1/4” 3-1/2” 2”
FTB040 FSA040 8,600 19-5/8” 5-1/2” 7/16” 32-3/4” 3-1/2” 2-1/8”
FTB063 FSA063 13,540 25-1/2” 6-3/8” 9/16” 45” 5-1/2” 2-3/8”
FTB080 FSA080 17,180 25-1/2” 6-7/8” 5/8” 49” 5-1/2” 2-3/8”
FTB125 FSA125 26,860 25-1/2” 8-1/2” 3/4” 60” 5-1/2” 3”
 
LIFTING LOOPS
Most economical lifting units for this system. Manufactured from flexible wire rope and tagged with a color code to match the capacity of the anchors. For tension only - limited to 30 degrees from vertical. Galvanized cable loop with mill finished threaded stud.
Part
Number		 Color Code System Capacity Tons Thread Size (D) Thread Length (E) Length (L)
TLL005 Orange 0.5 Rd12x1.75 3/4” 6-1/8”
TLL008 White 0.8 Rd14x2.0 7/8” 6-1/8”
TLL012 Red 1.2 Rd16x2.0 1” 6-1/8”
TLL016 Pink 1.6 Rd18x2.5 1-1/8” 7-1/2”
TLL020 Light Green 2 Rd20x2.5 1-1/4” 8-1/2”
TLL025 Dark Grey 2.5 Rd24x3.0 1-9/16” 10”
TLL040 Emerald Green 4 Rd30x3.5 2-3/16” 12”
TLL063 Light Blue 6.3 Rd36x4.0 2-5/8” 13-1/3”
TLL080 Light Grey 8 Rd42x4.5 3-1/8” 17”
TLL125 Yellow 12.5 Rd52x5.0 3-3/4” 19”
 
 

LIFTING LOOP WITH
PRESSURE PLATES
Most versatile lifting units for Waved Tail and Flat Steel Plate Anchors. Tagged with a color code to match the capacity of the anchors. Retain the flexibility of the regular Lifting Loops w/o the need for Distribution Basins when used in extreme shear conditions. Plated.

 
Part Number Color Code Sys. Capacity Tons Thread Size
TLP005 Orange 0.5 Rd12
TLP008 White 0.8 Rd14
TLP012 Red 1.2 Rd16
TLP016 Pink 1.6 Rd18
TLP020 Light Green 2 Rd20
TLP025 Dark Grey 2.5 Rd24
TLP040 Emerald Green 4 Rd30
TLP063 Light Blue 6.3 Rd36
TLP080 Light Grey 8 Rd42
TLP125 Yellow 12.5 Rd52
 

PLASTIC CAP
Used after casting to plug the
threaded opening in the anchors.
Grey plastic.

Part Number System Capacity Tons Thread Size Surface Dia. of Cap
TCS005 0.5 Rd12 3/4"
TCS008 0.8 Rd14 7/8"
TCS012 1.2 Rd16 1"
TCS012 1.6 Rd18 1-1/8"
TCS020 2 Rd20 1-1/4"
TCS025 2.5 Rd24 1-3/8"
TCS040 4 Rd30 1-3/4"
TCS063 6.3 Rd36 2-1/16"
TCS080 8 Rd42 2-3/8"
TCS125 12.5 Rd52 2-7/8"
 
 
   
DR | Threaded | Wire Rope | A-Anchor | Coils | Flat Steel | Manhole
Hebefix D8 | Transfix Anchor | Heba-T | Stone Strong | Recon & AW-Anchors
   
800-336-2598
 
 
   
 

Site designed by:
Multimedia X

© 2011 CONAC Corporation. All Rights Reserved
Tel: 1-800-336-2598
 
     
Home